Add to cart
BMR 15-17 S550 Mustang Super Low Profile Chassis Jacking Rails - Black Hammertone BMR 15-17 S550 Mustang Super Low Profile Chassis Jacking Rails - Black Hammertone $169.95
BMR 16-17 6th Gen Camaro Rear Of Rear Cradle Brace - Red BMR 16-17 6th Gen Camaro Rear Of Rear Cradle Brace - Red $229.95

BMR 15-17 S550 Mustang Cradle Bushing Lockout Kit Level 1 – Black

$109.95

Reduce Wheelhop, bushing deflection, and cradle movement on your S550 Mustang with a Level 1 Cradle Bushing Lockout Kit from BMR Suspension. Built from 6061-T6 billet aluminum and stainless steel, BMR’s CB010 Cradle Bushing Lockout Kit is designed to reduce cradle bushing deflection, which is one of the biggest causes of wheelhop. BMR’s CB010’s billet aluminum upper bushing lockout rings capture the inner bushing sleeve (front and rear) and the outer lip of the bushing cup on the cradle (front). The lower bushing locating washers (front) capture the bottom portion of the bushings’ inner sleeves. By capturing both parts of the bushings’ inner sleeves, movement on any plane (fore/aft, lateral, and vertical) is nearly eliminated. BMR Suspension designed the CB010 Cradle Bushing Lockout Kit for any application. This 100% bolt-on kit use existing boltholes and hardware, allowing for easy installation with simple hand tools. Once installed, the Cradle Bushing Lockout Kit reduces bushing and cradle deflection with nearly no change in NVH. (During BMR’s testing, no change in NVH was observed without accompanying modifications.) BMR Suspension’s CB010 Cradle Bushing Lockout Kit allows you yo affordably and effectively lessen wheelhop, bushing deflection, and cradle movement. Throughout testing, BMR has seen about an 80%-90% reduction in fore/aft and lateral cradle bushing deflection. A car with no other mods and stock tires that isn’t driven overly hard is going to see a 90% or higher reduction, while a more race oriented S550 with sticky tires will see slightly less of a reduction. Launching the test vehicle at over 7,000 rpm on drag radials, BMR saw about an 80% reduction in bushing deflection. Through the testing BMR has seen a 95% or greater reduction in vertical deflection in all testing situations. When performance is a must, rely on BMR Suspension! Installation time is 1-2 hours. Proudly made in the U.S.A.!
This 100% bolt-on kit use existing bolt-holes and hardware, allowing for easy installation with simple hand tools. Once installed, the Cradle Bushing Lockout Kit reduces bushing and cradle deflection with nearly no change in NVH.
100% bolt-on design;Works on Convertible model S550 Mustangs;Compatible with Steeda and other brand IRS Subframe ?Braces?;No fabrication needed;Installs with simple hand tools;CNC-machined 6061-T6 billet aluminum upper bushing lockout rings;Laser-cut lower bushing support washers;CNC-formed stainless steel lower bushing support plates;Greatly reduces stock subframe bushing deflection and wheel-hop;Uses factory bolt-holes and hardware;Durable Anodized finish;Proudly designed in the U.S.A.;Proudly built in the U.S.A

Add to Cart
BMR 15-17 S550 Mustang Cradle Bushing Lockout Kit Level 1 - Black
BMR 15-17 S550 Mustang Cradle Bushing Lockout Kit Level 1 - Black
$109.95
SKU: BMR-CB010 Category:
BMR Suspension logo

Free shipping on most orders over $250 using code “ShipFree” at checkout with destinations in the lower 48 states (Continental United States). Truck Freight, and oversize packaging are excluded.

  • 30 days easy returns
  • Most orders ship on the same day or within 48 hours
Guaranteed Safe Checkout

Reduce Wheelhop, bushing deflection, and cradle movement on your S550 Mustang with a Level 1 Cradle Bushing Lockout Kit from BMR Suspension. Built from 6061-T6 billet aluminum and stainless steel, BMR’s CB010 Cradle Bushing Lockout Kit is designed to reduce cradle bushing deflection, which is one of the biggest causes of wheelhop. BMR’s CB010’s billet aluminum upper bushing lockout rings capture the inner bushing sleeve (front and rear) and the outer lip of the bushing cup on the cradle (front). The lower bushing locating washers (front) capture the bottom portion of the bushings’ inner sleeves. By capturing both parts of the bushings’ inner sleeves, movement on any plane (fore/aft, lateral, and vertical) is nearly eliminated. BMR Suspension designed the CB010 Cradle Bushing Lockout Kit for any application. This 100% bolt-on kit use existing boltholes and hardware, allowing for easy installation with simple hand tools. Once installed, the Cradle Bushing Lockout Kit reduces bushing and cradle deflection with nearly no change in NVH. (During BMR’s testing, no change in NVH was observed without accompanying modifications.) BMR Suspension’s CB010 Cradle Bushing Lockout Kit allows you yo affordably and effectively lessen wheelhop, bushing deflection, and cradle movement. Throughout testing, BMR has seen about an 80%-90% reduction in fore/aft and lateral cradle bushing deflection. A car with no other mods and stock tires that isn’t driven overly hard is going to see a 90% or higher reduction, while a more race oriented S550 with sticky tires will see slightly less of a reduction. Launching the test vehicle at over 7,000 rpm on drag radials, BMR saw about an 80% reduction in bushing deflection. Through the testing BMR has seen a 95% or greater reduction in vertical deflection in all testing situations. When performance is a must, rely on BMR Suspension! Installation time is 1-2 hours. Proudly made in the U.S.A.!
This 100% bolt-on kit use existing bolt-holes and hardware, allowing for easy installation with simple hand tools. Once installed, the Cradle Bushing Lockout Kit reduces bushing and cradle deflection with nearly no change in NVH.
100% bolt-on design;Works on Convertible model S550 Mustangs;Compatible with Steeda and other brand IRS Subframe ?Braces?;No fabrication needed;Installs with simple hand tools;CNC-machined 6061-T6 billet aluminum upper bushing lockout rings;Laser-cut lower bushing support washers;CNC-formed stainless steel lower bushing support plates;Greatly reduces stock subframe bushing deflection and wheel-hop;Uses factory bolt-holes and hardware;Durable Anodized finish;Proudly designed in the U.S.A.;Proudly built in the U.S.A

Fitment:
2015 Ford Mustang EcoBoost
2015 Ford Mustang EcoBoost Premium
2015 Ford Mustang GT
2015 Ford Mustang GT 50 Years Limited Edition
2015 Ford Mustang GT Premium
2015 Ford Mustang Shelby GT350
2015 Ford Mustang V6
2016 Ford Mustang EcoBoost
2016 Ford Mustang EcoBoost Premium
2016 Ford Mustang GT
2016 Ford Mustang GT Premium
2016 Ford Mustang Shelby GT350
2016 Ford Mustang Shelby GT350R
2016 Ford Mustang V6
2017 Ford Mustang EcoBoost
2017 Ford Mustang EcoBoost Premium
2017 Ford Mustang GT
2017 Ford Mustang GT Premium
2017 Ford Mustang Shelby GT350
2017 Ford Mustang Shelby GT350R
2017 Ford Mustang V6
2018 Ford Mustang EcoBoost
2018 Ford Mustang EcoBoost Premium
2018 Ford Mustang GT
2018 Ford Mustang GT Premium
2018 Ford Mustang Shelby GT350
2018 Ford Mustang Shelby GT350R
2019 Ford Mustang Bullitt
2019 Ford Mustang EcoBoost
2019 Ford Mustang EcoBoost Premium
2019 Ford Mustang GT
2019 Ford Mustang GT Premium
2019 Ford Mustang Shelby GT350
2019 Ford Mustang Shelby GT350R
2020 Ford Mustang Bullitt
2020 Ford Mustang EcoBoost
2020 Ford Mustang EcoBoost Premium
2020 Ford Mustang GT
2020 Ford Mustang GT Premium
2020 Ford Mustang Shelby GT350
2020 Ford Mustang Shelby GT350R
2020 Ford Mustang Shelby GT500

Additional information

Weight 2 lbs
Dimensions 5.6 × 5.4 × 5.1 in
air_freight_prohibited

false
not_carb_approved

false
ltl_freight_required

false
prop_65

Unknown
part_type

automotive
epa

N/A
carb_acknowledgement_required

false
upc

887753331311
brand

BMR Suspension
part_number

CB010

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Brand

BMR Suspension

BMR Suspension - Performance Suspension and Chassis Components
BMR Suspension logo